 |
Acoustical Tee 5/8" Independent Support Clips
Provides Independent Support of Fixtures
No Installation Tools Required
Mounting Hardware Included
15/16" Grid Size
1/4-20 Stud
65lbs. Static Load Limit
|
 |
Acoustical Tee Fixture Suspension Bars
For Lightolier & Calculite series fixtures
Fully Adjustable
|
 |
Acoustical Tee Light Fixure Support
Lay-In & Troffer light fixture support clips
Upturned or Straight Lip fixtures
Fits round or rectangular head tee bar
|
 |
Acoustical Tee Snap On Box Hanger
Snaps easily onto tee bar
24" Span
Includes box mounting clip & 1/4"-20 screw
|
 |
Acoustical Tee Snap On Box Hanger - 8" Adj. Ht.
512A
8" height adjustable - 24" Span
|
 |
Acoustical Tee Snap On Box Hanger-Heavy Duty
Heavy Duty electrical box hanger with box mounting clip - 24" Span
50lbs Load Limit Per Bar
|
 |
Acoustical Tee T Bar Clip - Side Mount
Eliminates offset bending conduit
No installation tools required for basic clip
Provides a method of supporting conduit and outlet boxes above acoustical tee bar.
|
 |
Acoustical Tee T Bar Clip - Top Mount
Eliminates offset bending conduit
No installation tools required for basic clip
Provides a method of supporting conduit and outlet boxes above acoustical tee bar
|
 |
Acoustical Tee T Bar Fixure Support
For Light Fixtures
Reduces installation time
Position of fixture adjustable
No center clips required
Span adjustable 11" to 26"
|
 |
Acoustical Tee Twist On Fixture Support
Supports electrical fixtures from acoustical tee bar
Washer-wing nut & spacer included
|
 |
Acoustical Tee Twist On Track Light Clip
Easy installation
No tools required
|
 |
Beam Clamps
1-1/2" Conduit Hanger to Beam thru 1/2" flange
|
 |
Beam Clamps
Easy installation for beam flanges 1/8" to 5/8"
Supports 1/4" threaded rod, 1/4" threaded bridle rings & boxes.
Bright zinc finish
|
 |
Bridle Rings
Bridle rings not recommended for high performance cables
|
 |
Cable Snap Clips
Cable snap clip for AC / MC cable.
*Heat treated steel
Supports cable from 1/16" to 1/2" flange
Effective with MC AC cable dimensions 3/8" to 1-1/4
Clip snaps on flange and cable snaps into clip
|
 |
Cablecat Datacom Supports
Provides proper support of Category 5, Category 6, Fiber Optic and Interduct.
Complies with UL, cUL, NEC and EIA/TIA requirements for structured cabling systems.
|
 |
Conduit Hangers Flange/Wire/Plain Rod
Conduit Clips from flange, wire or rod.
Horizontal applications
Supports conduit to rods or flanges
|
 |
Conduit Hangers w/Bolts
Fast and easy installation – Installs with screwdriver or nut driver.
Mounting hole for 1/4" bolt. Retained bolt and built-in nut means there are less parts to handle or drop. Bright zinc finish.
Combo Head bolt ready to work with any tool handy - Slotted, Hex, #3 Phillips and #2 Robertson.
|
 |
Conduit Supports
Conduit hanger from flange, wire or plain rod.
MAC2 snaps in half to accommodate single run of cable effectively making two clips from one
Manufactured with stabilizer legs for virtually “wobble-free” support
One fastener for cable size 14-4, 12-4, 12-3, 12-2, 10-3, 10-2
Prepunched holes in clip allow it to be screwed to wood stud, concrete or block
Snaps into place on metal stud and beam flange up to 1/8" thick. No tools required for installation
|
 |
Drywall
Old Work box mounts
One-piece, break-apart design is easy to handle
Works on drywall, lathe and plaster; only a drywall saw required - Accommodates single or multiple gang boxes; for multiple gang boxes use (2) DSB’s. Can be placed at different locations on an electrical box to allow for more clearance.
Fastener installs before the box to free up your hands.
|
 |
Drywall
|
 |
Flange Mount Clips/Finger Close Clips
Available for M & P series rigid & aluminum conduit
Can be used with beam clamps for vertical & horizontal installation of conduit.
Available with plain hole for 1/4" bolt or 1/4-20 thread impression.
Clips have finger close capability.
|
 |
Hammer On Flange Clips
Provided with a 1/4-20 thread impression so box may be quickly and securely attached to the clamp.
Also available with staked stud 1/4-20 x 3/8" for easier attachment of outlet boxes to beams
|
 |
Hammer On Flange Clips
Hammer-On Flange Clips
Locates a portable 1/4" hole with just a hammer
Fits most beams and bulb tees
|
 |
ISN Smart Nut
Snaps anywhere on 3/8" - 16 threaded rod
Adjustable and removable
Supports plumbing, HVAC, electrical
|
 |
Metal Stud Adjustable Box Support
766A Supports 4" Electrical box from metal stud 2-1/2" 3-1/2" 4"
Steel, Zinc Plated
UL File E165702
|
 |
Metal Stud Box Mounting Brackets
For Between Studs
Supports electrical boxes, plaster rings or low voltage devices from one bracket.
Accomodates up to four 4" or 4-11/16" boxes
Mounts 1-1/2 or 2-1/8" deep boxes
Eliminates need for an electrical box on low voltage applications.
|
 |
Metal Stud Easy Snap Grommet
Snap one grommet into standard 1-11/32" field punched hole, OR snap tight two together into any shape factory punched hole
Provides 360° protection for cable and makes cable pulls easier.
Delivers compliance with: NEC®Article 300.4(b)(1) and CEC Rule 12-516.
CADDY® is a registered trademark of ERICO
CADDY® fasteners are intended for indoor use in non-corrosive environments only
|
 |
Metal Stud Flexible Conduit Clip
MC/AC Cable to Metal Stud
Attaches MC or AC to Metal Stud Easily
Provides fast installation
|
 |
Metal Stud Low Voltage Mounting Bracket - Double Gang
Attaches with self-tapping screws or nails
May be installed to the front or the side of the metal or wood stud.
Provides a bracket for mounting low voltage Class 2 communication outlets.
Reduces bulges in the dry wall caused by plaster rings.
Side support provides for a rigid installation
Bendable tabs provide cable tie off for 3/4" conduit stubbing
|
 |
Metal Stud Low Voltage Mounting Bracket - Single Gang
Attaches with self-tapping screws or nails
May be installed to the front or the side of the metal or wood stud
Provides a bracket for mounting low voltage Class 2 communication outlets
Reduces bulges in the dry wall caused by plaster rings.
Side support provides for a rigid installation
Works with 1/2" and 5/8" dry wall.
Bendable tabs provide cable tie off for 3/4" conduit stubbing
|
 |
Metal Stud Non-Metallic Cable Clip
Supports non-metallic cable
Not for use in Canada on NMC wire or power App.
|
 |
Metal Stud Punch
CADDY® is a registered trademark of ERICO
CADDY® fasteners are intended for indoor use in non-corrosive environments only
|
 |
Metal Stud Screw Gun Box Bracket
The TSGB Telescopic Screw Gun Bracket offers a unique, one-piece, break-apart design that makes mounting multiple runs of pipes between studs easier than ever. Requiring only a screw gun for installation TSGB is adjustable to allow non-standard stud spacing and features interlocking tabs for convenient identification and bending. The TSGB16 (article no. 187190) works with stud spacing from 280 mm to 458 mm, and the TSGB24 (article no. 187191) works with stud spacing from 432 mm to 660 mm.
(Pictured) Caddy# TSGB16
|
 |
Metal Stud Screw On Conduit Support
Alignment tab positively locates the fastener on the stud, keeping your conduit in line with box knock out and H-series brackets
Delivers compliance with: NEC Article 300.4(d) when used for 4" and 411/16" outlet boxes to metal or wood studs. CEC Rule 12-3012 for 4" and 411/16" outlet boxes to metal or wood studs.
For wood or metal stud
|
 |
Metal Stud Snap On Box Support
Center hole assists in consistent alignment, exact positioning and optional screw attachment
Attaches without hammer
Requires hammer to attach clip to box
|
 |
Metal Stud Universal Mounting Bracket
Easily attaches 4" and 4 11/16" outlet boxes to metal stud (HS3 for switch boxes)
Support leg reduces movement of box in wall
Can be attached to metal or wood stud
Offset design and use of #SMS8 low profile self-tapping screws (not included) reduce dry wall bulge
|
 |
Self-Tapping Metal Screws
Self Drilling/Tapping
Minimizes Drywall Bulge
Metal Stud Applications
|
 |
Strut Clamps/Multi-Function Clips
One size fits both EMT conduit and Rigid pipe sizes
One-piece break apart design includes captive combo head machine screw and built-in nut (thread impression)
Surface finish: electro zinc plated
|
 |
Strut Nuts
Unique 1 piece design
Eliminates the need for a washer
Quick attachment of threaded rod and hardware to all standard strut - regardless of depth
Unique one-piece design simply toggles into place and eliminates the need for a washer
Integrated plastic strip provides tension to grip the strut, even vertically
Easy to use and installs with just one hand
Can be installed in any position and is re-useable and adjustable
Applications
|
 |
Threaded Rod Brackets/Wire Hangers
Threaded Rod Brackets & Wire Hangers
(Pictured) Caddy# 4TI24
|
 |
Through Stud Cable/Conduit Support
Metal Stud conduit support
For horizontal runs of Rigid, EMT, MC/AC or ENT
through metal studs.
Eliminates conduit rattling.
|
